HOW TO APPLY THE DECALS

DECALS BAC111-500

Some tips how to apply BAC111-500 decals

 

General tips:

  • always use warm water with a drop of vinegar concentrate
  • put the decal in for 5 seconds
  • remove it and let it soak for approximately 30 seconds on the carrier paper
  • after soaking move the decal slowly on the carrier paper and apply it now to the kit
  • the decal is very thin, do not stretch it, that would ruin the print
  • do not use strong setting fluid
  • be patient, let the decal dry, it will straighten

 

 

The following pictures show you step by step how to apply the decals:

 

 

BEA-ANLEITUNG-1

 

BEA-ANLEITUNG-2

BEA-ANLEITUNG-3

BEA-ANLEITUNG-4

 

BEA-ANLEITUNG-5

 

BEA-ANLEITUNG-6

BEA-ANLEITUNG-7

 

After the cheatline parts you apply the cockpit window pieces.

 

BEA-ANLEITUNG-8

 

Now you have to apply the door 1 left and the emergency exits.

Afterwards the front and aft cabin windows, followed by...

 

BEA-ANLEITUNG-9

 

the windows on the emergency exits.

 

BEA-ANLEITUNG-10

 

You apply the right hand side decals in the same sequence.

 

The next step is the Royal Mail logo and the label on the door.

 

BEA-ANLEITUNG-11

 

 

You can choose between British Airways.......

 

BEA-ANLEITUNG-12

 

and British European Airways livery!

 

 

 

BEA-ANLEITUNG-13

 

 

Now we show you the detailed parts from front to rear:

 

BEA-ANLEITUNG-14

 

BEA-ANLEITUNG-16

BEA-ANLEITUNG-17

BEA-ANLEITUNG-18

BEA-ANLEITUNG-19

BEA-ANLEITUNG-22

BEA-ANLEITUNG-23

BEA-ANLEITUNG-24

 

 

The vertical stabilizator has four decal parts on each side.

I would recommend to cut off the small part on top and apply it separately. See the next picture:

 

BEA-ANLEITUNG_VERTICAL_STAB-1

 

You have to split the logo on the marking into 3 pieces and apply as follows:

 

BEA-ANLEITUNG_VERTICAL_STAB-2

BEA-ANLEITUNG_VERTICAL_STAB-3

BEA-ANLEITUNG_VERTICAL_STAB-4

 

 

Now the aft airstair:

There are 2 decals which are slightly wider. They are for the first 2 steps. 

 

BEA-ANLEITUNG_STAIR-1

 

After applying the step decals you can apply the BEA logos.

 

BEA-ANLEITUNG_STAIR-2

 

There is also a decal for the side of the stair depending on the registration you have chosen.

 

BEA-ANLEITUNG_STAIR-3

 

 

There are also nice inner circles for the wheels:

 

BEA-ANLEITUNG_REIFEN-1

BAC_main_gaer

 

The decal for the engine:

 

Engine_decal

 

The decal for the registration under the wing:

 

Wing_decal

 

 

On the following two pictures you see both sides of the kit with all decals applied: 

 

 

BEA-ANLEITUNG_COMPLETED-1

BEA-ANLEITUNG_COMPLETED-2

 

And here we have a picture of the 'half' finished kit:

 

BAC_50_fertig